Login

Rubber conveyor belt delamination during vulcanization usually results from a weak bond between layers or splice surfaces. The most common causes are contamination, poor surface preparation, trapped moisture or air, incompatible bonding materials, and incorrect or uneven curing conditions. Identifying which interface has separated—and checking the actual temperature, pressure, and cure time against the belt and bonding-material instructions—helps narrow down the cause. These parameters are not universal: the correct schedule depends on the belt construction, rubber compound, splice design, and vulcanizing equipment.
Click here to get more.
Delamination is the separation of bonded layers in a conveyor belt or splice. It may appear between rubber and fabric, between rubber and a steel-cord carcass, between cover and carcass, or along the bond line joining two belt ends. The location and appearance of the separation provide useful clues, but a visual check alone cannot always identify the root cause.
A splice-related failure is not the same as general belt-body delamination. A splice may lose adhesion because its prepared surfaces or bonding materials were unsuitable, while belt-body separation can involve the belt’s original construction, service damage, or a manufacturing issue. Record where the separation begins and which materials remain on each side before deciding what to change.
Dust, oil, grease, moisture, loose rubber, and other residue can interfere with contact between the surfaces being bonded. If old rubber or damaged fabric remains where the splice procedure calls for its removal, the new bonding layer may adhere to a weak surface rather than sound belt material. Preparation methods and the permitted amount of material removal should follow the belt supplier’s splice instructions.
Clean surfaces should be handled with care after preparation. Touching them with dirty gloves, setting tools on them, or allowing grinding debris to settle can reintroduce contamination. If a prepared surface becomes dirty or wet, do not assume that simply applying more adhesive will restore a reliable bond; confirm the correct remedy with the material supplier.
Splice compounds, uncured rubber, adhesives, and belt materials must be suitable for the belt construction and the specified vulcanizing process. Using a bonding material intended for a different rubber compound or splice design can result in poor adhesion or inconsistent curing. Material age, storage conditions, and handling can also matter, so check product identification and the supplier’s requirements before use.
Keep the full material system consistent with the approved procedure. Substituting one component, changing application methods, or mixing materials from different systems without confirmation can introduce an avoidable variable. When a failure occurs, retain package labels and lot details where available to help suppliers investigate.
Moisture on the belt or within bonding materials can compromise contact, while air pockets can leave areas without adequate surface-to-surface bonding. These defects may arise from damp storage, condensation, rushed assembly, uneven material application, or poor control when laying up the splice. They can be difficult to detect until the splice is inspected or begins to separate.
Follow the procedure for material conditioning and assembly, and protect prepared components from moisture and dust. Apply layers and close the splice in the sequence specified for the belt type. Avoid improvised methods to remove bubbles or dry materials, since heat and handling requirements vary by product.
Vulcanization depends on a controlled combination of temperature, pressure, and cure duration. A setting that is too low, too high, or applied for an unsuitable period can produce an undercured or overexposed bond, depending on the compound and process. The correct values must come from the belt and bonding-material specifications, not from a general rule of thumb.
Machine display values do not necessarily show the conditions at every point in the splice. As a practical diagnostic, record temperature readings at 3 positions across the platen and compare them with the specified schedule. A difference of 10 °C between measured zones is a reason to investigate heat distribution; it is an example for troubleshooting, not a universal rejection limit. Record pressure in MPa and cure duration in minutes, then compare both with the approved procedure.
With competitive price and timely delivery, Quanjinhe sincerely hope to be your supplier and partner.
A platen that is not positioned evenly, unsuitable press setup, inconsistent contact, or a pressure-system issue can create local variations across the bonding area. Those variations may leave one region under-cured or insufficiently consolidated even when the machine’s main display appears normal. Check platen condition, alignment, pressure distribution, and the setup method specified by the equipment and belt suppliers.
Also consider the splice’s geometry and the equipment’s working area. The vulcanizing press must suit the belt width and splice arrangement, and the load must be applied as intended by the manufacturer. Do not compensate for suspected unevenness by increasing the overall temperature or pressure without technical guidance.
If the belt ends or splice layers shift during assembly, the bond line may not have consistent contact. Incorrect alignment can also create uneven thickness or pressure, which complicates curing and later inspection. Use the specified reference marks and assembly sequence, and verify alignment before closing the press.
Opening the press, moving the belt, or applying tension before the procedure allows can disturb a bond that has not completed its required cycle or cooling stage. Follow the specified release and handling instructions. If the splice is loaded too early, the resulting damage may resemble a curing defect even when the initial materials and setup were suitable.
Begin by documenting the failure before removing or reworking the splice. Photograph the separation, note whether it follows a layer interface or crosses through the rubber, and record the location across the belt width. Preserve details about the belt construction, splice materials, preparation method, machine setup, and the cure conditions used.
| Observation | Possible factors to investigate | Useful checks |
|---|---|---|
| Clean separation along a bond line | Contamination, surface preparation, or material compatibility | Review preparation steps, material identification, and storage |
| Separation concentrated in one area | Local temperature or pressure variation, trapped air, or uneven assembly | Review platen readings, setup, and lay-up sequence |
| Soft, tacky, or otherwise inconsistent rubber | Possible cure-cycle or material-handling issue | Compare recorded conditions with the specified schedule |
| Separation within the belt body away from the splice | Possible belt construction, service, or broader material issue | Inspect surrounding belt and consult the belt supplier |
These observations are diagnostic starting points, not definitive proof of a cause. Several factors can occur together, such as contamination combined with uneven pressure. For a recurring problem, compare records from a successful splice with those from the failed one and change one controllable factor at a time where practical.
Build the splice procedure around the belt manufacturer’s instructions and the requirements for the specific bonding materials. Use a checklist for preparation, material verification, alignment, press setup, and release. Record the specified and observed temperature, pressure, and duration for each job so that deviations can be reviewed rather than guessed at later.
Confirm that the vulcanizing machine is suitable for the belt and splice dimensions, and inspect its heating and pressure systems according to the equipment manufacturer’s maintenance guidance. Check that the working surfaces are clean and positioned correctly. If readings or curing results vary between locations, arrange an appropriate equipment inspection instead of compensating with unverified settings.
When the same separation recurs, send the belt and material details, failure photographs, cure records, and machine information to the relevant technical suppliers. This gives them a basis to distinguish a process issue from a material mismatch or equipment concern. Avoid making a permanent change to the cure schedule until the responsible supplier confirms that it is appropriate.
The common causes of rubber conveyor belt delamination during vulcanization are contaminated or poorly prepared surfaces, incompatible or mishandled bonding materials, trapped moisture or air, incorrect curing conditions, uneven heat or pressure, and assembly or handling errors. The failure location can guide troubleshooting, but it should be considered alongside process records and the belt’s construction. The best starting point is to compare the documented splice procedure and actual machine conditions with the belt and material suppliers’ requirements.
For your next splice, verify the materials and preparation sequence, confirm the press setup, and record temperature at multiple positions, pressure, and cure duration. If you are selecting or reviewing a conveyor belt vulcanizing machine, share the belt width, splice design, operating requirements, and applicable cure procedure with the equipment supplier. At Quanjinhe, we can discuss vulcanizing machine considerations for your application and help you identify the technical details needed for a suitable equipment inquiry.
If you are looking for more details, kindly visit Common Causes of Rubber Conveyor Belt Delamination During Vulcanization.
1 0 0
Join Us

Comments
All Comments ( 0 )